2015-02-23, 11:03 PM
سلام
داخل سایت اوانیکس صفحه بلیزارد نوشته که میتوان قدرت تفنگ و فشار باد را می توان کم و زیاد کرد ( از پشت ماشه - مطابق عکس زیر ) .
آیا کسی از اعضا و اساتید هستند که روش آن را طبق عکس بلد باشند و یاد ما هم بدهند ( با تصویر باشد بهتر است )
با تشکر
و آیا باید قبل از این کار هوای داخل سیلندر را خالی کنم یا نمی خواهد ؟
اینم از دستورالعمل بلیزارد . لطفا اگر انگلیسی تون خوبه زحمت ترجمه اش را برای من و مابقی اعضا بکشید .
لطفا هر کسی می تونه تجربیاتشو به اشتراک بگذاره
Approx.25-30 shots on high power (before needing a refill)
Approx.150 shots on low power (before needing a refill)
Make sure the rifle is unloaded by removing the magazine and ensure there
are no pellets in the breech. Put the gun on SAFE.
Invert the rifle and secure it in a rifle stand or
similar stabilizing device. Remove the
stock.
First-stage adjustment
The adjustment screw for the first stage is situated
in the section underneath the trigger blade. Using
a 1.5mm Allen key, turn the screw clockwise to
decrease the amount of first-stage travel. Turn the
screw counterclockwise to increase the amount
of first-stage travel.
Second-stage and sear adjustment
This adjustment screw is situated in the sear
bar. Using a 1.5mm Allen key, turn the screw
clockwise to decrease the amount of secondstage
travel and sear engagement. Turn the screw
counterclockwise to increase the amount of
second-stage travel and sear engagement.
NOTE: This adjustment affects sear engagement.
It may be necessary to alter both adjustments to
achieve the desired setting. Adjustment of one
screw may affect other settings. Do not overadjust,
as this may cause the gun to fire prematurely or not operate correctly
and make the rifle unsafe. Always check your settings to ensure correct and safe
operation of the rifle. Always ensure that operation of the safety is unaffected by any
alterations you may make to the trigger mechanism.
Trigger blade position
To change the position of the trigger blade, undo the 2.5mm Allen headed bolt that
secures the trigger blade, and move it to a position of your choice.
Adjusting the trigger
Keep your finger off the trigger while cocking the air rifle.
داخل سایت اوانیکس صفحه بلیزارد نوشته که میتوان قدرت تفنگ و فشار باد را می توان کم و زیاد کرد ( از پشت ماشه - مطابق عکس زیر ) .
آیا کسی از اعضا و اساتید هستند که روش آن را طبق عکس بلد باشند و یاد ما هم بدهند ( با تصویر باشد بهتر است )
با تشکر
و آیا باید قبل از این کار هوای داخل سیلندر را خالی کنم یا نمی خواهد ؟
اینم از دستورالعمل بلیزارد . لطفا اگر انگلیسی تون خوبه زحمت ترجمه اش را برای من و مابقی اعضا بکشید .
لطفا هر کسی می تونه تجربیاتشو به اشتراک بگذاره
Approx.25-30 shots on high power (before needing a refill)
Approx.150 shots on low power (before needing a refill)
Make sure the rifle is unloaded by removing the magazine and ensure there
are no pellets in the breech. Put the gun on SAFE.
Invert the rifle and secure it in a rifle stand or
similar stabilizing device. Remove the
stock.
First-stage adjustment
The adjustment screw for the first stage is situated
in the section underneath the trigger blade. Using
a 1.5mm Allen key, turn the screw clockwise to
decrease the amount of first-stage travel. Turn the
screw counterclockwise to increase the amount
of first-stage travel.
Second-stage and sear adjustment
This adjustment screw is situated in the sear
bar. Using a 1.5mm Allen key, turn the screw
clockwise to decrease the amount of secondstage
travel and sear engagement. Turn the screw
counterclockwise to increase the amount of
second-stage travel and sear engagement.
NOTE: This adjustment affects sear engagement.
It may be necessary to alter both adjustments to
achieve the desired setting. Adjustment of one
screw may affect other settings. Do not overadjust,
as this may cause the gun to fire prematurely or not operate correctly
and make the rifle unsafe. Always check your settings to ensure correct and safe
operation of the rifle. Always ensure that operation of the safety is unaffected by any
alterations you may make to the trigger mechanism.
Trigger blade position
To change the position of the trigger blade, undo the 2.5mm Allen headed bolt that
secures the trigger blade, and move it to a position of your choice.
Adjusting the trigger
Keep your finger off the trigger while cocking the air rifle.